Real job 21 and 22 November 2026 · Mercedes C-Class C 220 d
The car would not start. The specialist never left his bench.
A C-Class bought at a salvage auction, a replacement engine control unit, and a car that still would not crank. One 22-minute session over the owner's phone hotspot showed where the start request stopped. A second session the next day found a stored crash event holding the starter back. Once it was reset, the car started on its own key.
Fault codes
- U014687Communication with the central gateway has a malfunctionread on both days
- P061500The electrical line A of the starter relay has an electrical faultstored, read on 22 November
- 22minutes. The first live session over the owner's phone hotspot, on 4G
- 1M+car communication messages carried to the specialist, about 780 every second
- 0miles travelled by the specialist. The car stayed in Bristol
From the car to the bench, live
An auction car and a £20 control unit.
The owner bought a Mercedes C-Class at a salvage auction. For it they had bought a used engine control unit online for £20. On these cars a replacement engine control unit does nothing until it is matched to the car's immobiliser. Several people had tried to match this one, and none had managed it.
The car's data, read from miles away.
The owner plugged a Gateway PRO into the car in Bristol. Through it John read what he needed from the car's electronic ignition switch, from his own bench, while the car stayed where it was.
Two control units on the bench.
With that data John matched a second used control unit, bought by us, on the bench. The owner drove over to collect it and brought the £20 unit along. It was stuck in its bootloader. John repaired its software and matched it to the car as well.
Fitted. Still no start.
The next day, a Saturday, the owner fitted the control unit. The engine would not crank, and the owner filmed it for the YouTube channel Mikes Mercs and other cars. The usual next step is a specialist travelling to the car, or the car travelling on a truck.
Twenty-two minutes on a phone hotspot.
John connected through the Gateway PRO over the owner's phone hotspot and read the live values while the owner turned the key. The immobiliser had issued its start enable. With the key held at start, the engine control unit saw the start request arrive. Its output to the starter stayed off, and one fault code was stored: U014687, communication with the central gateway. So the immobiliser and the matched control unit were doing their job. The start request arrived and stopped before the starter.
The proof: the engine runs.
John asked the owner to bypass the starter relay. The engine fired. The Gateway PRO's own voltage reading shows it: the battery drops to 9.6 V as the starter turns, then rises above 14 V while the alternator charges. The matched control unit runs the engine. What was left to find was why the starter was never driven.
The next day: every control unit asked.
On Sunday 22 November the Gateway PRO was still in the car. Working with John, DEX asked 99 control unit addresses for their fault memory, and 25 control units answered. The engine control unit still reported the missing message from the central gateway. It had also stored a second code: P061500, an electrical fault on the starter relay line.
Following the start signal.
The owner held the key at start for 50 seconds while DEX read the electronic ignition switch, the engine control unit and the front signal module in turn. The ignition switch showed the start signal switched on for the whole time. The battery voltage stayed between 11.3 and 11.8 V. A starter that turns pulls it far lower. The start signal left the ignition switch and stopped inside the engine control unit.
A crash the control unit still remembered.
One stored value in the engine control unit explained it. It reads: inhibit of engine start by crash event, and it was set. The live crash input read as not active, so this was a memory of an earlier event. Whether it was written in this car or in the car the used control unit came from, the data does not say. The control unit's own data lists a reset for it.
Reset from the bench. The car starts.
John ran that reset with his own diagnostic tool, remotely, with the car still in Bristol. The owner turned the key and the engine started, with no bypass on the starter relay. Two days, two remote sessions, and nobody travelled to the car.
The engine starts, seen from the bench
The specialist's screen during the session.

Key on, not yet at start. The start request at the engine control unit reads OFF.

Key held at start. The start request reads ON and the immobiliser's start enable reads YES. The output to the starter stays at NO.

The engine control unit's own summary. Engine start is enabled and all keys are enabled. The end of the vehicle number and the immobiliser identifiers are covered.
The owner's side, on YouTube: the day it would not start, from the channel Mikes Mercs and other cars.
Who did what.
- The specialist, JohnMore than twenty years in automotive electronics. Read the car from his bench, prepared both control units, ran the live sessions, chose the tests and reset the stored crash event.
- DEXWorked alongside John: watched the car's communication messages during the first session, logged it second by second and analysed the log afterwards. On the second day it read every control unit and followed the start signal while the key was held.
- The Gateway PROSat in the car's diagnostic socket and carried about 780 car communication messages a second to the bench over a phone hotspot. Every message sent to the car went out: none failed.
- The ownerPlugged in the Gateway PRO, shared a phone hotspot, turned the key, held it at start and bypassed the starter relay when asked. Films the work for the YouTube channel Mikes Mercs and other cars.
The pictures are the specialist's own screens from the session. The last four characters of the vehicle number and the immobiliser identifiers are covered. The reading of the live values is engineering judgement. The readings of 22 November only read from the car. The reset was done by the specialist. The start on the key was seen on the car. This is one job. Every fault is different, and a remote session does not find every one of them.